| Series 7000 - Proximity Sensors |
 |
Canfield Series 7000 magnetic proximity sensors are used to sense position on air cylinders from 2" to 8" bore. This proven design is rugged yet cost effective. Our magnetic proximity switch features a patented self adjusting clamp that grips standard NFPA and custom cylinders eliminating stocking requirements of many clamps for different bore sizes. |
| |
Series 7000 Catalog Page (1.10 MB .pdf) |
|
| |
|
|
| Series 7HL Hazardous Location Magnetic Proximity Sensors |
 |
The Canfield Connector 7HL is a rugged magnetic proximity sensor designed to sense actuator position in stringent, hazardous location applications. The switch features a robust, aircraft aluminum body, epoxy-filled, vibration and shock resistant, electronic circuit, and a 1/2" conduit female thread with hard-usage multi conductor cable. Available in a normally open contact, the 7HL can switch current up .5Amps and has a voltage range of 0-120VAC/VDC 50/60 Hz. |
| |
Series 7HL Catalog Page (233 KB .pdf) |
|
| |
|
|
| Series 7GL General Location Magnetic Proximity Sensors |
 |
The Canfield Connector 7GL is an expansion of the popular Series 7000
"floating" clamp design, which adapts to NFPA tie rod linear actuators with 2 to 8 inch bore. The switch features a robust, aircraft aluminum body, epoxy-filled, vibration and shock resistant, electronic circuit, and a 1/2 inch conduit female thread with multi conductor cable. Available in a normally open contact, the 7GL can switch current up to .5 Amps and has a voltage range of 0-120 VAC/VDC 50/60 Hz. |
| |
Series 7GL Catalog Page (219 KB .pdf) |
|
| |
|
|
| Series 8000 Proximity Sensors |
 |
The Canfield Connector Series 8000 reed and electronic proximity sensors are compact units designed for sensing applications on round cylinders from 9/16" - 4" bore, and tie-rod pneumatic cylinders from 3/4" - 2 1/2" bore. These sensors offer a wide voltage range from 0-120V AC/DC 50/60 Hz and high current capacity up to 0.5 Amps. They include high intensity indicator lights and a wide viewing angle. The sensors small package can fit easily on the smallest cylinder without appearing too large. The Series 8000's design promotes ease of installation with a tight fit. Options include 9 feet of PVC cable or 8 mm NEMA 4 quick connect housing version with or without a female mating cable and connector. |
| |
Series 8000 Catalog Page (752 KB .pdf) |
|
| |
|
|
| Series 8WS Reed and Electronic Magnet Sensors |
 |
The canfield Connector series 8WS reed and electronic magnet sensors
are rugged yet compact switches used to sense position on pneumatic
actuators equipped with a magnetic piston and 12mm dovetail groove. The switch can be slipped in and tightened from anywhere along the groove that is fabricated in to the cylinder wall or clamping system. The switch features a die cast holder which clamps to the cylinder groove while the electronics are fully encapsulated and resistance to environment. These sensors offer a wide voltage range from 0-120 V AC/DC 50/60Hz and have up to a 500mA switching current rating. The switch has a high intensity indicator light which indicates power to the switch and load. The switch comes standard with 9ft flexible pressure extruded cable or 6inch 8mm pigtail quick connector. |
| |
Series 8WS Catalog Page (429 KB .pdf) |
|
| |
|
|
| Series 9C Magnetic Sensors |
 |
The Canfield Connector Series 9C is a compact, universal, magnetically
operated proximity switch commonly used on aluminum extruded profile
type linear actuators equipped with magnetic pistons. The switches are
available in both reed and electronic styles and made to fit into a 4mm
key hole type slot. Other mounting variations include Tie-rod or
Cylinder clamp options. Position fixing is accomplished by means of a
screw that is supplied in the switch body. The onboard indicator light
shows instant switch diagnostics to minimize downtime and facilitate
installation and can be seen from wide angles. Unique to this switch is
the type 50 which incorporates sinking or sourcing output in the same
switch, eliminating the need for double inventory of switch types.
|
| |
Series 9C Catalog Page (378 KB .pdf) |
|
| |
|
|
| Series 9D Reed and Electronic Sensors |
 |
The Canfield Connector Series 9D is a universal, ultra-small magnetic proximity switch available in both solid state electronic and reed styles. These sensors are designed to fit the most stringent space requirements by use of a standard .250 inch dovetail slot. Many other mountings options are also avaiable. The electronic sensor exhibits greater sensitivity to magnetism with reduced dead-band and hysteresis as compared to competitive devices. The reed sensor offers a wide operating voltage range. The molded switch has an on board indicator light that can be viewed from wide angles. |
| |
Series 9D Catalog Page (519 KB .pdf) |
|
| |
|
|
| Series 9E Reed and Electronic Sensors |
 |
The Canfield Connector Series 9E is a universal, ultra-small, magnetic
proximity switch available in both solid state electronic and reed
styles. These sensors are designed to fit the most stringent space requirements by use of a standard .250 inch dovetail slot. Many other mounting options are also available. The electronic sensor exhibits greater sensitivity to magnatism with reduced dead-band and hysteresis as compared to competitive devices. The reed sensor offers a wide operating voltage range. The molded switch has an on board indicator light that can be viewed from wide angles. |
| |
Series 9D Catalog Page (519 KB .pdf) |
|
| |
|
|
| Series 9F Reed and Electronic Sensors |
 |
The Canfield Connector Series 9F is a universal, ultra-small, magnetic proximity switch available in both solid state electronic and reed styles. These sensors are designed to fit the most stringent space requirements by using a 4mm "T" slot. The electronic sensor exhibits greater sensitivity to magnetism with reduced dead-band and hysteresis as compared to competitive devices. The reed sensor offers a wide operating voltage range. The molded switch has an on board indicator light that can be viewed from wide angles. Standard connection to the sensor is provided by a 9 ft. cable or an optional industry standard 8mm circular connector with pig tail cable. The rugged 20% glass-filled polypropylene switch is shipped with mounting hardware ready for installation. |
| |
Series 9F Catalog Page (433 KB .pdf) |
|
| |
|
|
| Series 9M50 Magnetic Proximity Switch |
 |
The Canfield Connector 9M50 is compact full featured magnetic proximity
switch designed to fit a "D" shaped groove detail designed into linear actuators. Then innovative design allows the switch to be inserted anywhere along the linear actuator and then rotated and locked into position. When installed the switch lies flat against the cylinder housing and does not protrude beyond the cylinder face making installations neat and clean. The fully encapsulated switch is offered in reed, and electronic styles in either NPN or PNP. The robust epoxy encapsulated design meets IP67, NEMA 6 environmental protection. Voltage ranges are available from 5 to 120 VAC/DC in multiple versions. Maximum current draw is 200 mA. Standard wire lengths are 3 meters (9ft) wire leads or 8mm push or screw to connect connector. Female connector mating cords are available. |
| |
Series 9F Catalog Page (355 KB .pdf) |
|
| |
|
|
